-- *****************************************************************
-- CISCO-HSRP-MIB


-- Copyright (c) 1998-2005 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************

CISCO-HSRP-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,
    NOTIFICATION-TYPE,
    OBJECT-TYPE,
    IpAddress,
    Unsigned32
        FROM SNMPv2-SMI
    TEXTUAL-CONVENTION,
    DisplayString,
    TruthValue,
    RowStatus,
    MacAddress
        FROM SNMPv2-TC
    MODULE-COMPLIANCE,
    NOTIFICATION-GROUP,
    OBJECT-GROUP
        FROM SNMPv2-CONF
    ifIndex
        FROM IF-MIB
    ciscoMgmt
        FROM CISCO-SMI;

ciscoHsrpMIB MODULE-IDENTITY
    LAST-UPDATED    "200512200000Z"
    ORGANIZATION    "Cisco Systems, Inc."
    CONTACT-INFO
            "Cisco Systems
            Customer Service

            Postal: 170 W Tasman Drive
            San Jose, CA  95134
            USA

            Tel: +1 800 553-NETS

            E-mail: cs-hsrp@cisco.com"
    DESCRIPTION
            "The MIB module provides a means to monitor and configure
            the Cisco IOS proprietary Hot Standby Router Protocol
            (HSRP). Cisco HSRP protocol is defined in RFC2281.

            Terminology:

            HSRP is a protocol used amoung a group of routers for the
            purpose of selecting an 'active router' and a 'standby
            router'.

            An 'active router' is the router of choice for routing
            packets.

            A 'standby router' is a router that takes over the routing
            duties when an active router fails, or when preset
            conditions have been met.

            An 'HSRP group' or a 'standby group' is a set of routers
            which communicate using HSRP. An HSRP group has a group MAC
            address and a group Virtual IP address. These are the
            designated addresses. The active router assumes (i.e.
            inherits) these group addresses.

            'Hello' messages are sent to indicate that a router is
            running and is capable of becoming the active or standby
            router.

            'Hellotime' is the interval between successive HSRP Hello
            messages from a given router.

            'Holdtime' is the interval between the receipt of a Hello
            message and the presumption that the sending router has
            failed."
    REVISION        "200512200000Z"
    DESCRIPTION
            "Deprecated cHsrpCompliance and added cHsrpComplianceRev1
            to include cHsrpNotificationsGroup; Updated the imports
            such that Unsigned32 is imported from SNMPv2-SMI instead
            of CISCO-TC, and other clean-up."
    REVISION        "9808030000Z"
    DESCRIPTION
            "Initial version of this MIB."
    ::= { ciscoMgmt 106 }

-- Textual Conventions
HsrpState ::= TEXTUAL-CONVENTION
    STATUS          current
    DESCRIPTION
            "The current state of the HSRP protocol for a given
            HSRP group entry."
    SYNTAX          INTEGER {
                        initial(1),
                        learn(2),
                        listen(3),
                        speak(4),
                        standby(5),
                        active(6)
                    }

ciscoHsrpMIBObjects OBJECT IDENTIFIER
    ::= { ciscoHsrpMIB 1 }

cHsrpGlobalConfig OBJECT IDENTIFIER
    ::= { ciscoHsrpMIBObjects 1 }

cHsrpGroup OBJECT IDENTIFIER
    ::= { ciscoHsrpMIBObjects 2 }

-- Global Config Objects
cHsrpConfigTimeout OBJECT-TYPE
    SYNTAX          Unsigned32 (1..60)
    UNITS           "minutes"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
            "The amount of time in minutes a row in cHsrpGrpTable can
            remain in a state other than active before being timed out."
    DEFVAL          { 5 }
    ::= { cHsrpGlobalConfig 1 }

-- HSRP Tables
cHsrpGrpTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CHsrpGrpEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
            "A table containing information on each HSRP group
            for each interface."
    ::= { cHsrpGroup 1 }

cHsrpGrpEntry OBJECT-TYPE
    SYNTAX          CHsrpGrpEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
            "Information about an HSRP group. Management applications
            use cHsrpGrpRowStatus to control entry modification,
            creation and deletion.

            Setting cHsrpGrpRowStatus to 'active' causes the router to
            communicate using HSRP.

            The value of cHsrpGrpRowStatus may be set to 'destroy' at
            any time.

            Entries may not be created via SNMP without explicitly 
            setting cHsrpGrpRowStatus to either 'createAndGo' or 
            'createAndWait'.

            Entries can be created and modified via the management 
            protocol or by the device's local management interface.

            A management application wishing to create an entry should
            choose the ifIndex of the interface which is to be added
            as part of an HSRP group. Also, a cHsrpGrpNumber should
            be chosen. A group number is unique only amongst the groups 
            on a particular interface. The value of the group number
            appears in packets which are transmitted and received on a 
            LAN segment to which the router is connected. The application
            must select the group number as explained in the description
            for cHsrpGrpNumber.

            If the row is not active, and a local management interface
            command modifies that row, the row may transition to active
            state.

            A row which is not in active state will timeout after a
            configurable period (five minutes by default). This timeout 
            period can be changed by setting cHsrpConfigTimeout."
    INDEX           {
                        ifIndex,
                        cHsrpGrpNumber
                    }
    ::= { cHsrpGrpTable 1 }

CHsrpGrpEntry ::= SEQUENCE {
    cHsrpGrpNumber                  Unsigned32,
    cHsrpGrpAuth                    DisplayString,
    cHsrpGrpPriority                Unsigned32,
    cHsrpGrpPreempt                 TruthValue,
    cHsrpGrpPreemptDelay            Unsigned32,
    cHsrpGrpUseConfiguredTimers     TruthValue,
    cHsrpGrpConfiguredHelloTime     Unsigned32,
    cHsrpGrpConfiguredHoldTime      Unsigned32,
    cHsrpGrpLearnedHelloTime        Unsigned32,
    cHsrpGrpLearnedHoldTime         Unsigned32,
    cHsrpGrpVirtualIpAddr           IpAddress,
    cHsrpGrpUseConfigVirtualIpAddr  TruthValue,
    cHsrpGrpActiveRouter            IpAddress,
    cHsrpGrpStandbyRouter           IpAddress,
    cHsrpGrpStandbyState            HsrpState,
    cHsrpGrpVirtualMacAddr          MacAddress,
    cHsrpGrpEntryRowStatus          RowStatus
}

cHsrpGrpNumber OBJECT-TYPE
    SYNTAX          Unsigned32 (0..255)
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
            "This object along with the ifIndex of a particular interface
            uniquely identifies an HSRP group.

            Group numbers 0,1 and 2 are the only valid group numbers
            for TokenRing interfaces. For other media types, numbers
            range from 0 to 255. Each interface has its own set of group
            numbers. There's no relationship between the groups
            configured on different interfaces. Using a group number
            on one interface doesn't preclude using the same group
            number on a different interface. For example, there can be
            a group 1 on an Ethernet and a group 1 on Token Ring. More
            details can be found from RFC 2281."
    ::= { cHsrpGrpEntry 1 }

cHsrpGrpAuth OBJECT-TYPE
    SYNTAX          DisplayString (SIZE (0..8))
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "This is an unencrypted authentication string which is
            carried in all HSRP messages. An authentication string
            mismatch prevents a router interface from learning the
            designated IP address or HSRP timer values from
            other HSRP-enabled routers with the same group number.

            The function of this object is not to supply any sort of
            security-like authentication but rather to confirm that
            what's happening is what's intended. In other words, this
            is meant for sanity checking only."
    DEFVAL          { "cisco" }
    ::= { cHsrpGrpEntry 2 }

cHsrpGrpPriority OBJECT-TYPE
    SYNTAX          Unsigned32 (0..255)
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "The cHsrpGrpPriority helps to select the active and the
            standby routers. The router with the highest priority is
            selected as the active router. In the priority range of 0
            to 255, 0 is the lowest priority and 255 is the highest
            priority.

            If two (or more) routers in a group have the same priority,
            the one with the highest ip address of the interface is the
            active router. When the active router fails to send a Hello
            message within a configurable period of time, the standby
            router with the highest priority becomes the active
            router.

            A router with highest priority will only attempt to
            overthrow a lower priority active router if it is
            configured to preempt.  But, if there is more than one
            router which is not active, the highest priority non-active
            router becomes the standby router."
    DEFVAL          { 100 }
    ::= { cHsrpGrpEntry 3 }

cHsrpGrpPreempt OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "This object, if TRUE, indicates that the current router
            should attempt to overthrow a lower priority active router
            and attempt to become the active router. If this object is
            FALSE, the router will become the active router only if
            there is no such router (or if an active router fails)."
    DEFVAL          { false }
    ::= { cHsrpGrpEntry 4 }

cHsrpGrpPreemptDelay OBJECT-TYPE
    SYNTAX          Unsigned32 (0..3600)
    UNITS           "seconds"
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "This delay is the time difference between a router power
            up and the time it can actually start preempting the
            currently active router.

            When a router first comes up, it doesn't have a complete
            routing table. If it's configured to preempt, then it will
            become the Active router, but it will not be able to
            provide adequate routing services. The solution to this is
            to allow for a configurable delay before the router
            actually preempts the currently active router."
    DEFVAL          { 0 }
    ::= { cHsrpGrpEntry 5 }

cHsrpGrpUseConfiguredTimers OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "HSRP routers learn a group's Hellotime or Holdtime from
            hello messages.

            The Hellotime is used to determine the frequency of
            generating hello messages when this router becomes the
            active or standby router. The Holdtime is the interval
            between the receipt of a Hello message and the presumption
            that the sending router has failed.

            If this object is TRUE, the cHsrpGrpConfiguredHelloTime and
            cHsrpGrpConfiguredHoldTime will be used. If it is FALSE,
            the Hellotime and Holdtime values are learned."
    ::= { cHsrpGrpEntry 6 }

cHsrpGrpConfiguredHelloTime OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "milliseconds"
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "If cHsrpGrpUseConfiguredTimers is true,
            cHsrpGrpConfiguredHelloTime is used when this router is an
            active router. Otherwise, the Hellotime learned from the
            current active router is used. All routers on a particular
            LAN segment must use the same Hellotime."
    DEFVAL          { 3000 }
    ::= { cHsrpGrpEntry 7 }

cHsrpGrpConfiguredHoldTime OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "milliseconds"
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "If cHsrpGrpUseConfiguredTimers is true,
            cHsrpGrpConfiguredHoldTime is used when this router is an
            active router. Otherwise, the Holdtime learned from the
            current active router is used. All routers on a particular
            LAN segment should use the same Holdtime. Also, the
            Holdtime should be at least three times the value of the
            Hellotime and must be greater than the Hellotime."
    DEFVAL          { 10000 }
    ::= { cHsrpGrpEntry 8 }

cHsrpGrpLearnedHelloTime OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "milliseconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "If the Hellotime is not configured on a router, it can be
            learned from the Hello messages from active router,
            provided the Hello message is authenticated. If the
            Hellotime is not learned from a Hello message from the
            active router and it is not manually configured, a default
            value of 3 seconds is recommended."
    DEFVAL          { 3000 }
    ::= { cHsrpGrpEntry 9 }

cHsrpGrpLearnedHoldTime OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "milliseconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "If the Holdtime is not configured on a router, it can be
            learned from the Hello message from the active router.
            Holdtime should be learned only if the Hello message is
            authenticated. If the Holdtime is not learned and it is
            not manually configured, a default value of 10 seconds is 
            recommended."
    DEFVAL          { 10000 }
    ::= { cHsrpGrpEntry 10 }

cHsrpGrpVirtualIpAddr OBJECT-TYPE
    SYNTAX          IpAddress
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "This is the primary virtual IP address used by this
            group.  If this address is configured (i.e a non zero ip
            address), this value is used. Otherwise, the agent will
            attempt to discover the virtual address through a discovery
            process (which scans the hello messages)."
    DEFVAL          { '00000000'H }
    ::= { cHsrpGrpEntry 11 }

cHsrpGrpUseConfigVirtualIpAddr OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "If this object is TRUE, cHsrpGrpVirtualIpAddr was a
            configured one. Otherwise, it indicates that 
            cHsrpGrpVirtualIpAddr was a learned one."
    ::= { cHsrpGrpEntry 12 }

cHsrpGrpActiveRouter OBJECT-TYPE
    SYNTAX          IpAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "Ip Address of the currently active router for this group."
    ::= { cHsrpGrpEntry 13 }

cHsrpGrpStandbyRouter OBJECT-TYPE
    SYNTAX          IpAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "Ip Address of the currently standby router for this
            group."
    ::= { cHsrpGrpEntry 14 }

cHsrpGrpStandbyState OBJECT-TYPE
    SYNTAX          HsrpState
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "The current HSRP state of this group on this interface."
    ::= { cHsrpGrpEntry 15 }

cHsrpGrpVirtualMacAddr OBJECT-TYPE
    SYNTAX          MacAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
            "Mac Addresses used are as specified in RFC 2281. For
            ethernet and fddi interfaces, a MAC address will be in the
            range 00:00:0c:07:ac:00 through 00:00:0c:07:ac:ff. The last
            octet is the hexadecimal equivalent of cHsrpGrpNumber
            (0-255).

            Some Ethernet and FDDI interfaces allow a unicast MAC
            address for each HSRP group. Certain Ethernet
            chipsets(LANCE Ethernet, VGANYLAN and QUICC Ethernet) only
            support a single Unicast Mac Address. In this case, only
            one HSRP group is allowed.

            For TokenRing interfaces, the following three MAC 
            addresses are permitted (functional addresses):
                         C0:00:00:01:00:00
                         C0:00:00:02:00:00
                         C0:00:00:04:00:00."
    ::= { cHsrpGrpEntry 16 }

cHsrpGrpEntryRowStatus OBJECT-TYPE
    SYNTAX          RowStatus
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
            "The control that allows modification, creation, and
            deletion of entries.  For detailed rules see the
            DESCRIPTION for cHsrpGrpEntry."
    ::= { cHsrpGrpEntry 17 }

-- Notifications
cHsrpMIBNotificationPrefix OBJECT IDENTIFIER
    ::= { ciscoHsrpMIB 2 }

cHsrpMIBNotifications OBJECT IDENTIFIER
    ::= { cHsrpMIBNotificationPrefix 0 }

cHsrpStateChange NOTIFICATION-TYPE
    OBJECTS         { cHsrpGrpStandbyState }
    STATUS          current
    DESCRIPTION
            "A cHsrpStateChange notification is sent when a
            cHsrpGrpStandbyState transitions to either active or
            standby state, or leaves active or standby state. There
            will be only one notification issued when the state change
            is from standby to active and vice versa."
    ::= { cHsrpMIBNotifications 1 }

-- Conformance groups
cHsrpConformance OBJECT IDENTIFIER
    ::= { ciscoHsrpMIB 3 }

cHsrpCompliances OBJECT IDENTIFIER
    ::= { cHsrpConformance 1 }

cHsrpComplianceGroups OBJECT IDENTIFIER
    ::= { cHsrpConformance 2 }

-- compliance statements
cHsrpCompliance MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
            "The compliance statement for all hosts implementing
            the CISCO-HSRP-MIB."
    MODULE          -- this module
    MANDATORY-GROUPS {
                        cHsrpConfigGroup,
                        cHsrpGrpGroup
                    }
    ::= { cHsrpCompliances 1 }

cHsrpComplianceRev1 MODULE-COMPLIANCE
    STATUS          current
    DESCRIPTION
            "The compliance statement for all hosts implementing
            the CISCO-HSRP-MIB."
    MODULE          -- this module
    MANDATORY-GROUPS {
                        cHsrpConfigGroup,
                        cHsrpGrpGroup,
                        cHsrpNotificationsGroup
                    }
    ::= { cHsrpCompliances 2 }

-- units of conformance
cHsrpConfigGroup OBJECT-GROUP
    OBJECTS         { cHsrpConfigTimeout }
    STATUS          current
    DESCRIPTION
            "The collection of objects used to set global
            configuration objects for the HSRP MIB."
    ::= { cHsrpComplianceGroups 1 }

cHsrpGrpGroup OBJECT-GROUP
    OBJECTS         {
                        cHsrpGrpAuth,
                        cHsrpGrpPriority,
                        cHsrpGrpPreempt,
                        cHsrpGrpPreemptDelay,
                        cHsrpGrpUseConfiguredTimers,
                        cHsrpGrpConfiguredHelloTime,
                        cHsrpGrpConfiguredHoldTime,
                        cHsrpGrpLearnedHelloTime,
                        cHsrpGrpLearnedHoldTime,
                        cHsrpGrpVirtualIpAddr,
                        cHsrpGrpUseConfigVirtualIpAddr,
                        cHsrpGrpActiveRouter,
                        cHsrpGrpStandbyRouter,
                        cHsrpGrpStandbyState,
                        cHsrpGrpVirtualMacAddr,
                        cHsrpGrpEntryRowStatus
                    }
    STATUS          current
    DESCRIPTION
            "The collection of objects used to add, delete and
            retrieve information about HSRP groups."
    ::= { cHsrpComplianceGroups 2 }

cHsrpNotificationsGroup NOTIFICATION-GROUP
    NOTIFICATIONS   { cHsrpStateChange }
    STATUS          current
    DESCRIPTION
            "The collection of notifications used to indicate HSRP
            state information."
    ::= { cHsrpComplianceGroups 3 }

END